Ford 2005 E-150 Manual do Utilizador

Introduction 4Instrument Cluster 12Warning and control lights 12Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo cassette 20AM/FM stereo w

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

• Eight passenger wagon• Twelve passenger wagon• Fifteen passenger wagonrepresents LATCH anchors.represents tether strap anchors.Never attach two LATC

The lower anchors for child seatinstallation are located at the rearsection of the seat between thecushion and seat back.Follow the child seat manufac

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

VEHICLE CHARACTERISTICSHow your vehicle differs from other vehiclesSUV and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your veh

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs.Also inspect the tire sidewalls for cuts, b

pressure should never be set lower than the recommended pressure onthe tire label or certification label.When weather temperature changes occur, tire

Tire inflation informationAll tires with Steel Carcass Plies (if equipped):This type of tire utilizes steel cords in the sidewalls. As such, theycanno

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versusall-terrain) as those orig

different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse

To remove the spare tire:1. Open the rear doors and removethe thumb screw and anti-theftbracket. If finger pressure will notremove the thumb screw, us

4. Apply the parking brake and turnthe engine off.5. Block the wheel that is diagonallyopposite the tire you are changing.On E-450 vehicles, the parki

• the jack is located in the rearright-hand side of the cargo area.7. Use the tapered end of the lug nut wrench to unscrew wheelornaments attached by

• Never use the front or reardifferential as a jacking point.Rear axle jacking points - Allmodels except E-350 Dual RearWheel (DRW) and E-450:Rear axl

Front axle jacking points:Place the jack under the pin on thefront surface of the front axle.Do not place the jack under oron the steering linkage.• R

• 8-lug wheelNever use wheels or lugnuts different than theoriginal equipment as this coulddamage the wheel or mountingsystem. This damage could allow

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, as per your scheduled maintenanceinformation), or at

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheelor the surface of the fr

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new

8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n

which is located on the B-Pillar or the edge of the driver’s door. The coldinflation pressure should never be set lower than the recommendedpressure o

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance items:Tire wear

Safety practicesDriving habits have a great deal to do with your tire mileage and safety.• Observe posted speed limits• Avoid fast starts, stops and t

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Electronic throttle control (ifequipped): Illuminates when theengine has defaulted to a’limp-home’ operation. Report thefault to a dealer at the earli

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo).

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), a

6. If your vehicle will be towing a trailer, load from your trailer will betransferred to your vehicle. Consult this manual to determine how thisreduc

Special loading instructions for owners of pickup trucks andutility-type vehiclesFor important information regarding safe operation of this typeof veh

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Charging system: Illuminates whenth

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

GCWR (Gross Combined Weight Rating)/Trailer WeightsEngineRearaxleratioMaximumGCWR - lb.(kg)MaximumLoadedTrailer Weight- lb. (kg)Maximumfrontal area of

Your vehicle’s load capacity is designated by weight, not by volume, soyou cannot necessarily use all available space when loading a vehicle.Distribut

Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enoughbraking power and your chanc

Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni

Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or changedunless a

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the

Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (the key is not in the ignition) and thedriver’s doo

Starting the engine1. Turn the key to 4 (ON) withoutturning the key to 5 (START).2. Turn the key to 5 (START), thenrelease the key as soon as theengin

BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o

Parking brakeTo set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops.To release, pull the lever (2).Always set the parkin

A high crown in the road or high crosswinds may also make the steeringseem to wander/pull.TRACTION-LOK AXLE (IF EQUIPPED)This axle provides added trac

shift rearward. As a result, the van has less resistance to rollover andhandles differently from other commonly driven passenger vehicles,making it mo

• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a ma

Understanding the gearshift positions of the 4–speed automatictransmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adapti

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.(O

• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed.1 (First)• Provides ma

To put your vehicle in P (Park):• Come to a complete stop• Move the gearshift lever and securely latch it in P (Park)Always set the parking brake full

Odometer: Registers the total miles(kilometers) of the vehicle.Trip odometer: Registers the miles(kilometers) of individual journeys.Press the SELECT/

transmission is in the D (Overdrive) position; this engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescendin

Understanding the shift positions of the 5–speed automatictransmission (if equipped - diesel engines only)P (Park)This position locks the transmission

D (Drive) without OverdriveD (Drive) without Overdrive can beactivated by pressing thetransmission control switch (TCS)on the end of the gearshift lev

If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ea

A more complete description of PTO operation is discussed in the FordTruck Body Builders Layout Book, found atwww.fleet.ford.com/truckbbas.DRIVING THR

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

USING ROADSIDE ASSISTANCEComplete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, th

Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFF SWITCHThis device stops the electric fuel pump from sending fuel to

On commercial stripped chassisvehicles, this switch is located on abracket above the brake pedal.To reset the switch:1. Turn the ignition OFF.2. Check

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A 4–Wheel Anti–lock Brake System(4WABS) m

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 30A Radio capacitor(s), Ignition coil,Powertrain Control Module (PCM)diod

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description27 5A Radio28 — Not used29 — Not used30 15A Headlamps (high beam indicator)

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery orrefilling fluid reservoirs

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription8 40A** Trailer battery charge relay9 50A** Modified vehicle power10 30A** Electric b

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescriptionE — Trailer battery charge relayF — IDM relay (Diesel only)G — PCM relayH — Blower mo

Engine compartment relay moduleThe engine compartment relay module is located in one of two placesdepending on which type of engine your vehicle is eq

Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted.Do not attempt to push-start your vehicle. Automatictransmissions

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

AM/FM STEREO (IF EQUIPPED)1. Seek: Press/ to find thenext listenable station down/up thefrequency band.2. Tune: Press/ to manuallyadjust the radio fre

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caAway

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated righ

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed

Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa

5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your dealer or by writing toFord Motor Company of Canada, Limited, Service

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time.• Do not allow p

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft Engine Shampoo and Degreas

• Do not use abrasives, as they may cause scratches.• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned wit

Do not use cleaning solvents, bleach or dye on the vehicle’sseatbelts, as these actions may weaken the belt webbing.LEATHER SEATS (IF EQUIPPED)Your le

Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A)Motorcraft Detail Wash (ZC-3–A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Sham

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide sc

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

Seating and Safety Restraints 66Seating 66Safety restraints 72Air bags 82Child restraints 86Tires, Wheels and Loading 102Tire Information 105Tire Infl

AM/FM STEREO CASSETTE (IF EQUIPPED)1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTEngine compartment component locationsRefer to the 6.0 Liter Power Stroke Direct Injection Turbo Diese

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine isoverfilled, some oil must beremoved from the e

economy requirements of the International Lubricant Standardization andApproval Committee (ILSAC), comprised of U.S. and Japaneseautomobile manufactur

mineral or alkali content). If possible, however, try to only fill the batterycells with distilled water. If the battery needs water often, have thech

Battery posts, terminals and related accessories contain lead andlead compounds. Wash hands after handling.For information on transmission operation a

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

next selection). Then, press REW (for the beginning of the currentselection) or FF (to advance to the next selection). The tape MUST havea blank secti

coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl

Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut

What you should know about fail-safe cooling (if equipped)If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempor

Never remove the coolant reservoir cap while the engine isrunning or hot.5. Re-start the engine and take your vehicle to a service facility.Driving th

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al

RefuelingFuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others:• Read and follow all the instr

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any

with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage.Fuel qualityIf you are experiencing

Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcr

• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu

14. Bass: Press / todecrease/increase the bass output.15. Treble: Press/ todecrease/increase the treble output.16. EJ (Eject): Press to eject atape.17

• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.•You may want to t

EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. Th

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v

soon light is on, refer to the description in the Warning lights andchimes section of the Instrument Cluster chapter. Your vehicle may notpass the I/M

Check the fluid level when it is at ambient temperature, 20° – 80° F(-7° – 25° C):1. Check the fluid level on the dipstick. It should be between the a

TRANSMISSION FLUIDChecking automatic transmission fluid (if equipped)Refer to your scheduled maintenance information for scheduledintervals for fluid

You can check the fluid without driving if the ambient temperature isabove 50°F (10°C). However, if fluid is added at this time, an overfillcondition

Automatic transmission fluid filter (if equipped)The TorqShift automatictransmission is equipped with aserviceable external fluid filtermounted on the

Changing the air filter element1. Disconnect the fresh air inlet tubefrom the radiator support.2. Open the clamp that secures thetwo halves of the air

Component14.6L V8 engine 5.4L V8 engine 6.8L V10engineOil filter FL-820-S FL-820-S FL-820-SPCV valve2Spark plugs3Automatictransmissionfilter4— FT-145

2. FADE: Press / to shiftsound to the front/rear speakers.3. SCN (Scan): Press to hear abrief sampling of all listenablestations or CD tracks. Press a

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoi

Fluid Ford PartNameApplication CapacityPower steeringfluidMotorcraftMERCON威 ATFAll Keep in FULLrange ondipstickRear axle4SAE 75W-140Synthetic RearAxle

Fluid Ford PartNameApplication CapacityFuel tank N/A All regular andextended lengthvans and wagons35.0 gallons(132.4L)138 inchwheelbase(except E-Super

3Fill Dana rear axles to 1/4 inch to 9/16 inch (6 mm to 14 mm) belowbottom of fill hole. Fill Visteon axles 1/4 inch to 9/16 inch (6 mm to 14mm) below

LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluidPM-1 ESA-

Item Ford partnameFord partnumberFordspecificationAutomatictransmission(4R70/75 E)1MotorcraftMERCON威VATFXT-5-QM MERCON威VAutomatictransmissionTorqShift

Item Ford partnameFord partnumberFordspecificationDana LimitedSlip Axles3M60 (M248)E-250/350M70FF(M267FF)E-350M70HD(M273HD)E-450SAE 90 HypoidGear OilC

Some transmission fluids may be labeled as dual usage, such asMERCON威 and MERCON威 V. These dual usage fluids are not to be usedin an automatic transmi

VEHICLE DIMENSIONSVan/wagon modelsE-150 – Inches(mm)E-250 –Inches (mm)E-350 –Inches (mm)(1) Overallheight80.7 (2050) 82.9 (2107) 84.6 (2148)(2) Trackf

Cutaway/commercial stripped chassis modelsE-350 – inches (mm) E-450 – inches (mm)(1) Overall height Refer to Body Builder for specifications.(2) Track

11. TUNE: In radio mode, press tomove up or down the frequencyband in individual increments.12. SEEK: Press and releaseSEEK/ for previous/nextstrong s

VEHICLE IDENTIFICATION NUMBERComplete Ford built vehiclesThe vehicle identification number is attached to your vehicle in thefollowing places:• On the

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel. The following table tells you wh

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Leather wrapped steering wheelsScuff platesSpeed controlLifestyleMobile-ease hands-free communication systemTrailer hitches, wiring harnesses and acce

AAccessory delay ...56Air bag supplementalrestraint system ...82and child safety seats ...84d

Clock adjust6-CD in dash ...26, 30, 34AM/FM ...19AM/FM/Cassette ...20AM/FM/CD .

FFail safe coolant ...212Fluid capacities ...230Four-Wheel Drive vehiclespreparing to drive yourvehicle ...

Lane change indicator(see Turn signal) ...45Lights, warning and indicator ...12anti-lock brakes (ABS) ...151Load limits .

Spark plugs,specifications ...228, 237–238Special notice ...9ambulance conversions ...8diesel-powere

PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)1. Seek: Press and releaseSEEK/ for previous/nextstrong station, or track of thecurrent disc.2. Rewin

6. Bass: Press BASS; then pressSEL/ to decrease/increasethe bass output.Treble: Press TREB; then pressSEL/ to decrease/increasethe treble output.7. Se

10. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a preset button until soundreturns.11. CD: Press to

17. Disc tune: Radio: Pressor to manually tune down or upthe radio frequency band. CD:Press/ to select the previous/next CD.SATELLITE COMPATIBLE AM/FM

reception is available through your dealer. Detailed Satellite instructionsare included with the dealer installed kit.Dealer installed satellite kit o

Maintenance and Specifications 198Engine compartment 200Engine oil 201Battery 204Engine Coolant 207Fuel information 213Air filter(s) 228Part numbers 2

stored in preset 1 will begin playing. If there are less than six strongstations, the system will store the last one in the remaining presets.Setting

17. BAND: Press to toggle betweenAM/FM1/FM2 frequency band.18. Memory presets: To set astation: Select frequency band; tuneto a station, press and hol

instructions are included with the dealer installed kit.Dealer installed satellite kit only available in the continental UnitedStates.For information

changing to the next field. (TEXT must be pressed within 3 seconds ofthe previous button press to proceed to the next/last text display.)TEXT is also

Compression: Brings soft and loud CD passages together for a moreconsistent listening level when in CD mode. Press MENU untilcompression status is dis

16. SAT (if equipped): Your radiocomes equipped with Satellite Readycapability. The kit to enable theSatellite reception is available through your dea

23. Disc/Tune: Press or tomanually tune down/up the radiofrequency band, or to listen to theprevious/next CD.CAT: CAT is only available when equipped

• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes

HEATER ONLY SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature selection:Controls the tempe

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop.REAR FAN SPEED ADJUSTMENT (IF

HEADLAMP CONTROL• The first position turns on theparking, tail, license plate andside marker lamps.• The outer position turns on theheadlamps.Battery

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the ON position,• the head

PANEL DIMMER CONTROLTo adjust the brightness of theinstrument panel, rotate the dimmercontrol clockwise/counterclockwisewhen the headlamp control is i

3. Turn on the low beam headlampsand open the hood.4. Locate the high intensity area ofthe beam pattern and place the topedge of the intensity zone ev

8.• Aerodynamic: Locate the horizontal adjuster (1) for each headlamp.Turn it clockwise or counterclockwise, to place the left edge of thehigh intensi

Third row courtesy/reading/cargo lampsThe dome portion of the lamp, thecenter light, can be turned on whenthe headlamp control is rotated fullycounter

Function Number ofbulbsTrade numberHeadlamps (sealed beam) 2 H5054Headlamps (aerodynamic) 2 9007Park lamp and turn signal (front) 2 4157K or 3157KBack

4. Remove the bulb retaining ring byrotating it counterclockwise, andslide the ring off the plastic base.5. Pull the bulb straight out.Handle a haloge

3. Remove the four headlamp bulbretaining screws and the retainingring.4. Remove the headlamp.5. Disconnect the electricalconnector from the bulb and

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Replacing license plate lamp bulbs1. Turn the headlamp switch to OFFand then remove the two screwsand the license plate lamp assemblyfrom the rear doo

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl

CompassThe compass display is contained in the overhead console. The vehicleheading is displayed as one of N, NE, E, SE, S, SW, W and NW.The compass r

• Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles untilCAL indicator turns off in about 2–3 complete circles.• The compass is now calib

Always keep the power point caps closed when not being used.POWER WINDOWS (IF EQUIPPED)Do not leave children unattended in the vehicle and do not letc

Standard mirrorThe spotter mirror only can be tiltedfrom top to bottom. Move the lowermirror manually up/down to increaseside and rear visibility. App

The telescoping feature (ifequipped) allows the mirror toextend approximately 3.15 inches(80 mm). This feature is especiallyuseful to the driver when

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES contro

BREAKING-IN YOUR VEHICLEDuring the first 1,000 miles (1,600 km) of driving, maintain speeds below70 mph (110 km/h) and vary speeds frequently. This is

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of

KEYSThe key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.You

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The typ

Sounding a panic alarmPressto activate the alarm. Press the control again, or turn theignition to the 1 (ACCESSORY) or 4 (ON) position to deactivate t

Note: Replacement of the battery will not cause the remote transmitterto become deprogrammed from your vehicle. The remote transmittershould operate n

Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.The illuminated e

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Pull lever up to adjust seatback.Using the manual lumbar supportThe lumbar support control islocated on the inboard side of thedriver’s seat.Turn the

Press to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Quick release captains cha

Stow the tongue end of thedetachable anchor.2. Pull the seat latch handle, thenpull the seat toward the right side ofthe vehicle to disengage four pin

Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even

REAR SEATSAccessing the 3rd, 4th and 5th row seats (if equipped)To make access to the 4th and 5throw seats easier, attach the 3rd and4th row passenger

2. Pull the LH/RH seat latch handles(located under the seat) rearward torelease the latch hook ends from thefront strikers.3. Move the seat rearward a

SAFETY RESTRAINTSSafety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.To reduce

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Checkseat covers and buckle

Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

Front safety belt height adjustmentThe driver and front seat outboardpositions are equipped with a heightadjuster. Adjust the height of theshoulder be

Shorten and fasten the belt whennot in use.Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cl

If... Then...The driver’s safety belt is notbuckled approximately5 seconds after the safety beltwarning light has turned off...The BeltMinder娂 feature

Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder娂 reminds us to take a fewseconds to buckle up.“Seat belts don’t w

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

Do not sit on top of a buckled safety belt to avoid the BeltMinder娂 chime. Sitting on the safety belt will increase the riskof injury in an accident.

4. Within 10 seconds of the light turning on, at a moderate speed, bucklethen unbuckle the safety belt.• This will disable the BeltMinder娂 feature for

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Neverplace a rear-facing child

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burn

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit.Do

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Using your vehicle as a stationary power source (PTO)Refer to the Driving chapter for more information and guidelines foroperating a vehicle equipped

Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e

• LATCH lower anchors are recommended for use by children up to48 pounds (22 kg) in a child restraint. Top tether anchors can be usedfor children up t

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted.6. Allo

Attaching safety seats with tether strapsChildren should be placed in the rear in an appropriate childsafety seat that is properly secured to the vehi

Front passenger seating positionThe tether can be attached directlyto the rear of the front seat.1. Position the child safety seat onthe front right-h

4. Clip the tether strap hook to theseat pedestal to the location shown.5. Adjust the front right handpassenger seat to the full rearwardposition.6. I

Second row bucket seats (Chateau Quads)The tether strap can be attacheddirectly to the tether bracket underthe back edge of the seat cushion.1. Positi

Second, Third and Fourth row three passenger bench seatsThe tether strap can be attacheddirectly to the tether bracketprovided under the back edge of

For additional important safety information on the proper use of seatbelts, child seats and infant seats, please read the entire Seating andSafety Res