Ford 1999 F-350 Manual do Utilizador

Before drivingIntroduction 2Instrumentation 5Controls and features 22Seating and safety restraints 82Starting and drivingStarting 107Driving 112Roadsi

What you should do if the Service Engine Soon light illuminatesLight turns on solid:This means that the OBD II system has detected a malfunction.Tempo

2. Child age 12 or under: A child age 12 or under must ride in thefront seat because:• my vehicle has no rear seat;• although children age 12 and unde

Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children ride in yo

A belt-positioning booster should be used if the shoulder belt rests infront of the child’s face or neck, or if the lap belt does not fit snugly onbot

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent ac

Rear facing child seats should NEVER be placed in the frontseats.2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt togethe

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching safety seats with tether strapsSome manufacturers make safety seats that include a tether strap thatgoes over the back of the vehicle seat a

PREPARING TO START YOUR VEHICLEEngine starting is controlled by the ignition system. This system meetsall Canadian Interference-Causing Equipment stan

2. Make sure the headlamps and vehicle accessories are off.If starting a vehicle with an automatic transmission:• Make sure the parking brake isset.•

Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced.• If the driver’s safety belt is faste

Transmission control indicator light (TCIL) (if equipped)The word OFF located on the endof the gearshift lever is thetransmission control indicator li

Using the engine block heater (if equipped)An engine block heater warms theengine coolant, which improvesstarting, warms up the engine fasterand allow

Engine exhaust, some of its constituents, and certain vehiclecomponents contain or emit chemicals known to the State ofCalifornia to cause cancer, and

BRAKESYour service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance.Occasional brake noise is normal and o

Using RABS• In an emergency, applying full pressure may cause the front wheels tolock. If the front brakes lock, the vehicle cannot be steered. Yousho

With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminate

Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (manual tra

Extended use of other than the manufacturer’s specified size tires on aTraction-Lok rear axle could result in a permanent reduction ineffectiveness. T

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn off the ignition whenever you leaveyour vehicle.If the park

N (Neutral)With the gearshift in N (Neutral),the vehicle can be started and isfree to roll. Hold the brake pedaldown while in this gear.(Overdrive)The

2 (Second)Use 2 (Second) to start-up onslippery roads or to provideadditional engine braking ondowngrades.1 (First)Use 1 (Low) to provide maximumengin

Turn signalIlluminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orfla

4. Turn ignition to position 5(START) to start the engine, let theengine idle for a few seconds, thenshift into gear.5. Release the brake pedal.6. Rel

Maximum downshift speeds16-speed transmissionShift from: Transfer case position (if equipped)22H or 4H 4LD(Overdrive) - 4 72 km/h (45 mph) 26 km/h (16

2. Set parking brake.3. Shift into 1 (First).4. Turn the ignition key to position3 (OFF).Do not park your vehicle in Neutral, it may move unexpectedly

With the 5-speed transmission youcan shift into R (Reverse) only bymoving the gearshift from left of 3(Third) and 4 (Fourth) gears beforeyou shift int

Removing key from ignition• Turn the ignition key until itstops.• Push the release lever forwardand rotate the key towards youand remove.POWER TAKE OF

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED)When Four–wheel drive (4WD) is engaged, power is supplied to all fourwheels through a transfer case. 4WD

• automatic hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK.Manual 4x4 system (if equipped)The 4WD system is enga

Shifting from 2H (2WD high) to 4H (4WD high)Engage the locking hubs by rotatingthe hub lock control from FREE toLOCK, then move the transfer caselever

4. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4WD High) or 4L (4WD Low).Using the N (Neutral) positionThe transfer case neut

Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high)Rotate the 4WD control to the 4x4HIGH position at speeds up to 88km/h (55 mph).• Do not shift into

Door ajarIlluminates when the ignition is inthe ON or START position and anydoor is open.Oil pressure/Engine coolantThis light will illuminate when th

4. Move the 4WD control to the 4x4HIGH or 4x4 LOW position.Driving off-road with 4WDYour vehicle is specially equipped for driving on sand, snow, mud

SandWhen driving over sand, try to keep all four wheels on the most solidarea of the trail. Do not reduce the tire pressures but shift to a lowergear

If vehicle speed drops more than 16 km/h (10 mph), the speed controlwill cancel automatically. Resume speed with accelerator pedal.If speed control ca

• GVWR (Gross Vehicle Weight Rating) : Maximum total weight ofthe base vehicle, passengers, optional equipment and cargo. TheGVWR is specific to each

weight to the front of your vehicle, (potentially including weight addedto the cab), the weight added should not exceed the Front Axle ReserveCapacity

Driving through deep water where the transmission is submergedmay allow water into the transmission and cause internaltransmission damage.TOWING A TRA

Trailer towing tablesF-250 with manual transmissionEngine Rear axleratioMaximum GCWR-kg(lbs.)Maximum trailerweight-kg (lbs.)15.4L 3.73 6 124 (13 500)

F-350 with automatic transmissionEngine Rear axleratioMaximum GCWR-kg(lbs.)Maximum trailerweight-kg (lbs.)15.4L 3.73 6 124 (13 500) 4 536 (10 000)5.4L

Preparing to towUse the proper equipment for towing a trailer, and make sure it isproperly attached to your vehicle. See your dealer or a reliable tra

Trailer brakesElectric brakes and manual, automatic or surge-type brakes are safe ifinstalled properly and adjusted to the manufacturer’s specificatio

GAUGESFuel gaugeDisplays approximately how muchfuel is in the fuel tank (when theignition is in the ON position). Thefuel gauge may vary slightly when

Servicing after towingIf you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your Scheduled Maint

• 4x2 vehicles must have the driveshaft removed if the rear wheels areto be kept on the ground. If only the front wheels will be on theground, the dri

• After installing a snowplow to the vehicle, ensure the vehicle’s fronttoe alignment and front ride height are within specification (reset ifrequired

Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford orLincoln-Mercury dealer.Engine temp

HAZARD FLASHERUse only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when theignit

Use the following procedure to reset the fuel pump shut-off switch.1. Turn the ignition to the OFF position.2. Check the fuel system for leaks.3. If n

Standard fuse amperage rating and colorCOLORFuseRatingMiniFusesStandardFusesMaxiFusesCartridgeMaxiFusesFuse LinkCartridge2A Grey Grey — — —3A Violet V

To remove a fuse use the fuse pullertool provided on the fuse panelcover.The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingDescription1 2

Fuse/RelayLocationFuse AmpRatingDescription8 5A Radio, Headlamp Switch Illumination9 — Not Used10 — Not Used11 10A Washer Pump, Wiper Run/Park Relay C

Fuse/RelayLocationFuse AmpRatingDescription27 10A Ignition Run Power Feed (CustomerAccess)28 10A Brake Shift Interlock, DRL Relay Coil,Speed Control M

Engine coolant temperature gaugeIndicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal ar

The high-current fuses and relays are coded as follows.Fuse/RelayLocationFuse AmpRatingDescription1 7.5A * Trailer Tow Left Stop/Turn Lamp2 10A* Air B

Fuse/RelayLocationFuse AmpRatingDescription7 20A*(Gasolineonly)5A* (Dieselonly)Gasoline only-Vapor Managment Valve,HEGO Sensors, Intake ManifoldCommun

Fuse/RelayLocationFuse AmpRatingDescription27 -(Gasolineonly)30A*(Dieselonly)Gasoline only-Not UsedDiesel only-Injector Driver Module28 30A** Trailer

If your vehicle is equipped with 4WD, a spare tire of a differentsize than the road tires should not be used. Such a tire couldresult in damage to dri

2. The following steps are required to move the support bracket (ifequipped) away from the spare tire:• With tapered end of lug wrench,loosen the eyeb

5. The following steps are required to secure the support bracket (ifequipped) under the spare tire:• Move the support bracket over the spare tire.• S

5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.When one of the rearwheels is

• Front (4x2)• Front passenger side (4x4)Roadside emergencies157

• Front driver side (4x4)Make sure the jack fits into thenotched area on the differentialhousing.• RearRoadside emergencies158

8. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire.9. Remove the lug nuts with the

Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the control.TachometerIndicates the engine speed inrevolutions p

• Front (4x2)• Front driver side (4x4)• Front passenger side (4x4)Roadside emergencies160

• Rear14. Insert the jack handle into thepump linkage.15. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground.Hy

The following steps apply to all vehicles:19.Remove the jack and fully tightenthe lug nuts in the order shown.20. Stow the flat tire. Refer toStowing

JUMP STARTING YOUR VEHICLEThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury

Connecting the jumper cables1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.On

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

Engine oil pressure gaugeThis shows the engine oil pressurein the system. Sufficient pressureexists as long as the needle remainsin the normal range (

Working with the engine off• Automatic transmission:1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Turn off the e

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine oil dipstick2. Clutch fluid reservoir (manual transmission)3. Brake fluid reservoir4. Power

2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan.3. Set the parking brake and ensure the gearshift is securely latch

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedtha

2. Visually inspect the fluid level.3. If necessary, add brake fluid untilthe level reaches MAX. Do not fillabove this line.4. Use only a DOT 3 brake

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir.2. Remove cap and rubberdiaphragm from reservoir.3. Add

ENGINE COOLANTCheck the level of the enginecoolant in the reservoir. Refer to theScheduled Maintenance Guide forservice interval schedules. Be sureto

• DO NOT MIX recycled coolant and conventional coolanttogether in your vehicle. Mixing of engine coolants may harmyour engine’s cooling system.• The u

Mode controlEach press of the MODE control willdisplay a different feature as follows:Average fuel economy. Thedisplay will indicate the vehicle’saver

Recycled engine coolantFord Motor Company recommends that Ford and Lincoln-Mercurydealers use recycled engine coolant produced by Ford-approvedprocess

How fail-safe cooling worksIf the engine begins to overheat:• the engine coolant temperaturegauge will move to the red (hot)area.• thesymbol will illu

Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to aservice facility as soon as possi

operated for an extended period at high speeds, in city traffic during hotweather or pulling a trailer, the vehicle should be turned off for about 30m

The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]).High fluid levelFluid levels above the safe rangemay re

Checking and adding manual transmission fluid1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Fluid level should be at

Checking and adding transfer case fluid1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throught

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• if the vehicle is started while parked on an incline.• if less than 30 liters (8 gallons) of fuel is added to the fuel tank.The fuel range function

INFORMATION ABOUT TIRE QUALITY GRADESNew vehicles are fitted with tiresthat have their Tire Quality Grade(described below) molded into thetire’s sidew

Temperature A B CThe temperature grades are A (the highest), B, and C, representing thetire’s resistance to the generation of heat and its ability to

• Four tire rotation• Five tire rotationMaintenance and care192

Replacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix radial bias-belted,

The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and ch

Automotive fuels can cause serious injury or death if misused ormishandled.Observe the following guidelines when handling automotive fuel:• Extinguish

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke whilerefueling. Fuel vapor is extreme

with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage.Fuel qualityIf you are experiencing

4. To install the cap, align the tabs on the cap with the notches on thefiller pipe.5. Turn the filler cap clockwise 1/8 of a turn until it stops.If t

driving (engine break-in period). You will get a more accuratemeasurement after 3 000 km–5 000 km (2 000 miles-3 000 miles).Filling the tankThe advert

ICONSIndicates a safety alert. Read thefollowing section on Warnings.Indicates vehicle information relatedto recycling and otherenvironmental concerns

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Locate the trip computer

5. Follow one of the simple calculations in order to determine fueleconomy:Multiply liters used by 100, then divide by total kilometerstraveled.Divide

• Resting your foot on the brake pedal while driving may reduce fueleconomy.• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of Km/L (MPG) expected onthe vehicle

sells, leases, trades vehicles, or supervises a fleet of vehicles are notpermitted to intentionally remove an emission control device or preventit fro

• Tail lamps• Back-up lampsDo not remove lamp bulbs unless they can be replaced immediately withnew ones. If a bulb is removed for an extended period

Replacing headlamp bulbs (sealed beam)To remove the headlamp bulb:1. Make sure headlamp switch is in OFF position.2. Open the hood.3. Remove the two s

Replacing tail lamp/Backup lamp bulbsThe tail lamp/backup lamp bulbs arelocated in the same portion of thetail lamp assembly, one just belowthe other.

To install the brakelamp assembly:1. Install the bulb into the lamp assembly and rotate clockwise.2. Install the lamp assembly on the vehicle with two

AIMING THE HEADLAMPSThe alignment of your headlamps should be checked by a qualifiedservice technician if:• Oncoming motorists frequently signal you t

Waxing your vehicleWax when water stops beading on the surface. This could be every threeor four months, depending on operating conditions.Use only ca

Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines.For optimum calibration, turn o

Cleaning plastic exterior partsUse vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners,

Cleaning and maintaining the safety beltsClean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach

MOTORCRAFT PART NUMBERSComponent* 5.4L V8 engine 6.8L V10 engineAir filter element FA-1634 FA-1634Fuel filter FG-986B FG-986BOil filter FL-820-S FL-82

Fluid Ford Part Name Application CapacityEnginecoolant5Premium EngineCoolant5.4L V8 enginewithout A/C16.9L(17.9 quarts)5.4L V8 enginewith A/C18.4L(19.

Fluid Ford Part Name Application CapacityTransmissionfluid3SyntheticMERCON威 ATF5-speed manual 3.2L(3.4 quarts)MotorcraftMERCON威 ATF6-speed manual 5.5L

LUBRICANT SPECIFICATIONSItemFord partname orequivalentFord partnumberFordspecificationFront axle(4X4)Motorcraft SAE75W90 AxleLubricantXY-75W90-QL WSP-

ItemFord partname orequivalentFord partnumberFordspecificationHinges, latches,striker plates,fuel filler doorhinge and seattracksMulti-PurposeGreaseDO

ENGINE DATAEngine 5.4L V8 engine 6.8L V10 engineCubic inches 330 415Horsepower 235 @ 4250 rpm 275 @ 4250 rpmTorque 335 lb.-ft. @ 3000 rpm 410 lb.-ft.

F250-Crew cabDimension Body styleCrew Cab 4x2 Crew Cab 4x4(1) Overall height 1 960 mm (77.2 in)a/1 883 mm (74.1 in)b2 053mm (80.8 in)a/2 052 mm (80.8

(5) Overalllength5 732 mm(225.7 in)5 754 mm(226.5 in)5 879 mm(231.4 in)a/6 288 mm(247.6 in)b6 291 mm(247.7 in)aShort wheel basebLong wheel basecSingle

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlam

(4)Wheelbase3 576 mm(140.8 in)4 186 mm(164.8 in)4 475 mm(176.2 in)4 475 mm(176.2 in)(5) Overalllength5 732 mm(225.7 in)a6 341 mm(249.6 in)b---aShort w

32154Capacities and specifications221

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification Label be affixedt

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program

Ford extended service planYou can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. For

Getting the service you needAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. When you need warranty re

Please have the following information available when contacting FordCustomer Assistance:• Your telephone number (home and business)• The name of the d

• sales disputes between customer and dealer except those associatedwith warranty repairs or concerns with the vehicle’s performance asdesigned• a req

Your dealership and a Ford Motor Company representative are asked tosubmit statements at this time.To properly review your case, the Board needs the f

the Board are binding on Ford (and, in some cases, on the dealer) butnot on consumers who are free to pursue other remedies available tothem under sta

Flash to passPull toward you to activate andrelease to deactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headl

FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Business Park #3Allen Park, Michigan 48101U.S.A.Telephone: (313) 594-4

A wide selection of accessories is available through your local authorizedFord, Lincoln-Mercury or Ford of Canada dealer. These qualityaccessories hav

Travel equipmentConsoleConsole armrestDaytime running lightsFactory luggage rackFactory luggage rack adaptorsFog lightsFramed luggage coversHeavy-duty

Carpet floor matsCleaners, waxes and polishesFlat splash guardsFront end covers (full and mini)Hood deflectorsLocking gas capLubricants and oilsMolded

• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould im

Accessory delay ...75Air bag supplementalrestraint system ...92and child safety seats ...93de

Ford Extended Service Plan...224Getting assistance outside theU.S. and Canada ...229Getting roadside assistance ...223Getting the se

GAWR(Gross Axle Weight Rating) ...132calculating ...134definition ...132driving with a hea

Parking brake ...114Parts (see Motorcraft parts) ...212Power distribution box (seeFuses) ...

AUXILIARY POWER POINTThe auxiliary power point is locatedon the instrument panel.Do not plug optional electricalaccessories into the cigarette lighter

Vehicle Identification Number(VIN) ...222Vehicle loading ...132Ventilating your vehicle

241

242

243

244

245

246

247

Item InformationRequired fuel Unleaded fuel only - 87 octaneFuel tank capacity Refer to Refill capacities in the Capacitiesand specifications chapter.

• (Panel) -Distributes outside air through the instrument panelregisters.• OFF-Outside air is shut out and the fan will not operate.•(Panel and floor)

Do not place objects on top of the instrument panel, as theseobjects may become projectiles in a collision or a sudden stop.Manual heating and air con

• MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisierthan A/C but more economical and will cool the inside of the vehiclefaster. Air

Operating tips• In humid weather, select before driving. This will reduce yourwindshield from fogging. After a few minutes, select any desiredposition

USING YOUR AUDIO SYSTEMAM/FM StereoAM/FM Stereo1 2 3 4 AM/FMSEEKTONECLKTUNETONE VOL12FMST DXVOLPUSHON1 2 3 4 AM/FMSEEKTONECLKTUNETONE VOL12FMST DXVOLP

SPECIAL NOTICESNotice to owners of diesel-powered vehiclesRead the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’sGuide Supplement for in

Volume/power controlPress the control to turn the audiosystem on or off.Turn the control to raise or lowervolume.If the volume is set above a certain

Tune adjust in radio mode• Press to move to the nextfrequency down the band(whether or not a listenablestation is located there). Hold thecontrol to m

Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.With the electronic AM/FM stereo,press the TONE con

Setting the clockPress CLK to toggle betweenlistening frequencies and clockmode.To set the hour, press and hold theCLK control and press:•to decrease

reverting back to the clock. In media mode, the media information willalways be displayed.AM/FM stereo cassetteVolume/power controlPress the control t

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition

Seek function in radio mode• Press to find the nextlistenable station down thefrequency band.• Pressto find the nextlistenable station up thefrequency

Bass adjustThe bass adjust control allows youto increase or decrease the audiosystem’s bass output.Treble adjustThe treble adjust control allows youto

Tape select• To enter tape mode while in radiomode, press the TAPE AMScontrol.Automatic Music SearchThe Automatic Music Search featureallows you to qu

Dolby姞 noise reductionDolby威 noise reduction operatesonly in tape mode. Dolby威 reducesthe amount of hiss and static duringtape playback.Press thecontr

If your vehicle is equipped with theFord ambulance preparationpackage, it will be indicated on theCertification label. The label islocated on the driv

• to decrease minutes and• to increase minutes.The CLK control will allow you to switch between media display mode(radio station, stereo information,

Volume/power controlPress the control to turn the audiosystem on or off.Audio power can also be turned onby pressing the AM/FM selectcontrol or the ta

Tune adjustThe tune control works in radio or CD changer mode.Tune adjust in radio mode• Pressto move to the nextfrequency down the band(whether or no

Seek function in radio mode• Press to find the nextlistenable station down thefrequency band.• Pressto find the nextlistenable station up thefrequency

Scan function in tape modePress the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the

Starting autoset memory preset1. Select a frequency using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong stationsare

Press the TREB control then press:• to decrease the treble outputand•to increase the treble output.Speaker balance adjustSpeaker sound distribution ca

Tape/CD select• To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton duri

Eject functionPress the EJ control to stop andeject a tape.Press the EJ control to stop andeject a CD.Dolby noise reductionDolby noise reduction reduc

Setting the clockTo set the hour, press and hold theCLK control and press SEEK:•to decrease hours and•to increase hours.To set the minute, press and h

Instrumentation5

The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock

Your audio system is equipped with selective lighting, a unique lightingstrategy. This lighting feature is operable when the headlamps areilluminated.

AM/FM select in radio modeThis control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset

Seek function in radio mode• Press to find the nextlistenable station down thefrequency band.• Pressto find the nextlistenable station up thefrequency

Scan function in tape modePress the SCAN control to hear a short sampling of all selections on thetape. (The tape scans in a forward direction. At the

Starting autoset memory preset1. Select a frequency using the AM/FM select controls.2. Press the AUTO control.3. When the first six strong stationsare

Press the TREB control then press:• to decrease treble output and•to increase treble output.Speaker balance adjustSpeaker sound distribution can beadj

Tape/CD/CD changer (if equipped) select• To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE cont

Tape direction selectPress SIDE 1–2 to play the alternateside of a tape.Eject functionPress the control to stop and eject atape and/or a CD.Dolby nois

Setting the clockPress the clock/RDS control untilSELECT HOUR is displayed andpress:•to decrease hours and• to increase hours.To set the minute, press

0000000000MPH20km/h4060801001201401600102030405060708090100LOWFUELDOORAJARBRAKEFUELRESETLOWRANGE4 X 4!ABS+ -LEFHRPM1000X0123564PRN 218C18HDFUEL FILL

Radio Data System (RDS) featureThis feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations.Press and hold the c

RDS select program type• Press the RDS control until FINDprogram type is displayed.• Use the SEL control to select theprogram type. With the featureon

• Use the SEL control to selectTYPE, NAME, TEXT or NONE.When your radio is turned to aRDS station, RDS station TYPE,station NAME, or TEXT messagewill

Press to eject the magazine.Make sure only one disc is insertedin each slot. Each disc must beinserted with the label surfaceupward. Depending on your

Troubleshooting the CD changer (if equipped)The laser beam used in the compact disc player is harmful to theeyes. Do not attempt to disassemble the ca

• Do not expose tapes to direct sunlight, high humidity, extreme heat orextreme cold. Allow tapes that may have been exposed to extremetemperatures to

The audio system automatically switches to single channel reception if itwill improve the reception of a station normally received in stereo.Audio sys

SPEED CONTROL (IF EQUIPPED)To turn speed control on• Press ON.Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30

To set a speed• Press SET/SET ACC/SET ACCEL.For speed control to operate, thespeed control must be ON andthe vehicle speed must be greaterthan 48 km/h

You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe pr

123456FM1STSCANEJREWFFSIDE 1-2COMPSHUFFLETAPECDDISCSBASSTREBBALFADEAUTOSETVOL - PUSH ONSEEKTUNEAMFMwA/CMAXA/COFFOFFOFFONPASSENGER AIR BAGOVERDRIVEWD4X

To disengage speed control• Depress the brake pedal or• Depress the clutch pedal (ifequipped)Disengaging the speed control willnot erase the previousl

To return to a previously set speed• Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).TILT STE

HAZARD FLASHERFor information on the hazard flasher control, refer to Hazard flasher inthe Roadside emergencies chapter.WINDSHIELD WIPER/WASHER CONTRO

FLASH TO PASSPull toward you to activate andrelease to deactivate.OVERDRIVE CONTROL (IF EQUIPPED)Activating overdrive(Overdrive) is the normal drive p

POWER WINDOWS (IF EQUIPPED)Press and hold the rocker switches to open and close windows.• Press the top portion of therocker switch to close.• Press t

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press

2. Move the control in the directionyou wish to tilt the mirror.3. Return to the center position to lock mirrors in place.Fold-away mirrorsPull the si

REMOTE ENTRY SYSTEM (IF EQUIPPED)The remote entry system allows you to lock or unlock all vehicle doorswithout a key.The remote entry features only op

Sounding a panic alarmPress this control to activate thealarm.To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.This de

To replace the battery:1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APA

WARNING LIGHTS AND CHIMESLow fuelIlluminates as an early reminder of alow fuel condition indicated on thefuel gauge. The light comes on whenthere is a

Replacing lost transmittersTake all your vehicle’s transmittersto your dealer if service is required.If you purchase additionaltransmitters (up to fou

TAILGATE LOCK (IF EQUIPPED)Your vehicle is equipped with atailgate lock designed to preventtheft of the tailgate.• Insert ignition key and turn to the

SEATINGFull bench seat (if equipped)• Lift the release bar to move theseat forward or backward. Ensurethat the seat is relatched intoplace.• Pull up o

Captain’s chair (if equipped)• Lift the release bar to move theseat forward or rearward. Makesure that the seat is relatchedinto place.• Pull the seat

Press to raise or lower the rearportion of the seat cushion.Press the control to move the seatforward, backward, up or down.Using the manual lumbar su

Rear folding bench seat (if equipped)Folding down the rear seatsAll safety belts should beproperly stowed in the seatpockets before folding down there

1. Lift/rotate the seatback toward the rear of the vehicle and make sureit latches securely.2. Lift/rotate the lower seat cushion to its seating posit

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Combination lap and shoulder bel

Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt

• Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode.H

What you should do if the Check Engine/Service Engine Soon lightilluminatesLight turns on solid:This means that the OBD I system has detected a malfun

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position...The safety belt wa

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important supplemental restraint system (SRS) precautionsThe supplemental restraint systemis designed to wo

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.Steps you can take to properl

How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decele

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag is inflated, the air bag will not function

Disposal of air bags and air bag equipped vehicles(including pretensioners)For disposal of air bags or air bag equipped vehicles, see your localdealer

In order to avoid inadvertent activation of the switch, alwaysremove the ignition key from the passenger air bag ON/OFFswitch.Turning the passenger ai

Always transport children who are 12 and younger in the rearseat. Always use safety belts and child restraints properly. If achild in a rear facing in

• although children ages 1 to 12 ride in the rear seat(s) wheneverpossible, children ages 1 to 12 sometimes must ride in the frontbecause no space is