Ford 2010 F-150 v.1 Manual do Utilizador

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Message center 22Entertainment Systems 40AM/FM stereo 40AM/FM stereo with CD/M

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Resuming a set speedPress the RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing speed whil

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal or theclutch pedal (if equipped). Thiswill not era

In any mode:• Press VOL + or VOL - to adjustthe volume.SYNC威 system hands freecontrol features (if equipped)Pressbriefly to use the voicecommand featu

For further information on the Navigation system/SYNC威 system, refer tothe Navigation and SYNC威 supplements.MOON ROOF (IF EQUIPPED)The moon roof contr

The moon roof has a built-in sliding shade that can be manually openedor closed when the glass panel is shut. To close the shade, pull it towardthe fr

Do not use the HomeLink威 Wireless Control System with any garagedoor opener that lacks safety stop and reverse features as required byU.S. federal saf

• If the indicator light stays on constantly, programming is completeand your device should activate when the HomeLink威 button is pressedand released.

signal has been accepted by the HomeLink威. The indicator light willflash slowly and then rapidly after HomeLink威 accepts the radiofrequency signal.• P

For questions or comments, contact HomeLink威 at www.homelink.comor 1–800–355–3515.Car2U姞 Home Automation System (if equipped)The Car2U威 Home Automatio

Types of garage door openers (rolling code and fixed code)The Car2U威 Home Automation System may be programmed to operaterolling code and fixed code ga

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the

Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

Tailgate removalYour tailgate is removable to allow more room for loading.WARNING: Always properly secure cargo to prevent shiftingcargo or cargo fall

Tailgate step (if equipped)Your vehicle may be equipped with a feature that allows easier entry intothe truck bed. To open the tailgate step:1. Flip d

Note:• Fully close and latch the tailgate step before moving the vehicle.• Never drive with the step or grab handle deployed.• Replace slip resistance

To stow the box side step, with your foot, push the box side step underthe truck until fully latched. Do not push on the button while stowingthe box s

2. Open the latches to release thepanels.3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect th

5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged intotheir holes in the pick-up box.6. Reverse

WARNING LIGHTS AND CHIMESStandard instrument clusterPlatinum instrument clusterInstrument Cluster122010 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)

CARGO MANAGEMENT SYSTEM (IF EQUIPPED)The cargo management system consists of the Cargo rail package withthe following as optional accessories:• Front

Note: When replacing a cleat into the rail, make sure the oval embossedon the knob is not upside down. This will ensure that the cleat isproperly orie

Cross bars: Aluminum cross bars with T-slot channels in all four sides,and a latch mechanism that allows the end supports to snap over theexisting cle

Bed divider: This panel will keep small items up to 400 lb (180 kg) inposition in the pickup box. Also includes T-slots to allow attachment ofindustry

Side mounted tool bins: Watertight bins can be positioned at any pointalong the side rails and can be easily removed (even when full), andcarried to w

• To remove the bin from the rail, open lid and pull up on both leverslocated on the outboard edge (next to the pickup box top rail) untilthe handles

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

AutolockThe autolock feature is available on vehicles with power locking. Thisfeature will lock all the doors when:• all the doors are closed,• the ig

6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was deactivated or twice (one short and one longchirp) i

Deactivating/activating autounlock featureYour vehicle comes with the autounlock features activated; there are fourmethods to enable/disable this feat

Harley Davidson instrument clusterWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repa

4. Press and hold the 3 • 4. While holding the 3 • 4, press and releasethe 7 • 8. While still holding the 3 • 4, press and release the 7 • 8asecond ti

The typical operating range for your remote entry transmitter isapproximately 33 feet (10 meters). A decrease in operating range couldbe caused by:• w

Switching from two step to one step door unlockingYour vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and on

Activating the memory featureTo activate this feature:1. Position the seat, power mirrors, adjustable pedals and steeringcolumn (if equipped) to the d

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR

Programming remote transmittersIt is necessary to have all (maximum of four — original and/or new) ofyour remote transmitters available prior to begin

• after 25 seconds of illumination.The dome lamp control (if equipped) must not be set to the off positionfor the illuminated entry system to operate.

• the control is pressed on the remote entry transmitter.• the ignition is turned from the off position to the on position, or fromthe on position to

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEMSecuriLock威 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

Anti-theft indicatorThe anti-theft indicator is located in the instrument cluster.• When the ignition is in the offposition, the indicator will flasho

Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to Onboard diagnost

Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLock威 keys can be used. To program a coded key yourself, youwill

If not successful, the new coded key(s) will not start the vehicle’s engineand the theft indicator will flash on and off and you may repeat Steps 1thr

Create a MyKey™To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. Turnthe

Disable MyKey™To reset all MyKeys™ as Admin keys do the following:1. Turn the vehicle on using the Admin key.2. Press SETUP until PRESS RESET TO CLEAR

2. Remote start the vehicle using a remote start fob.3. Follow steps 1-4 in the Create a MyKey™ section.Note: For all vehicles, the number of MYKEY(S)

TroubleshootingCondition Potential CausesCan’t create a MyKey™ • Key in the ignition is already aMyKey™• Key in the ignition is the lastremaining Admi

Condition Potential CausesLost any key • For programming spare keys, referto the Programming spare keyssection in this chapter.I accidentally programm

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Front seat• Lift the track release bar

• Pull the release lever handlelocated on the side of the seat upto move the seatback forward orbackward.Using the armrest (if equipped)• Push the rel

• To gain access to the storagecompartment (if equipped) inyour armrest, lift the latch toopen the lid.Using the manual lumbar supportFor more lumbar

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press the forward side of the control

The control is located on the outboard side of the seat cushion.Move the switch in the direction ofthe arrows to raise or lower thefront portion of th

Memory seat/power mirrors/adjustable pedals/steering column(if equipped)This system allows automaticpositioning of the driver seat,outside rearview mi

The easy out feature automatically moves the driver’s seat 2 inches(5 cm) backward when:• the transmission is in P (Park)• the key is removed from the

Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur

Heated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjury, medication,

Climate controlled seats air filter replacement (if equipped)The climate controlled seat system includes air filters that must bereplaced periodically

Door ajar (RTT): Displays whenthe ignition is in the on position andany door is open.Engine coolant temperature(RTT): Illuminates when the enginecoola

To install a filter:• First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on t

To adjust the head restraint, do the following:1. Raise the head restraint bypulling up on the head restraint.2. Lower the head restraint bypressing a

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Folding up the rear seats (SuperCab on

• Rotate seat cushion up by liftingon the corner until it locks intovertical storage position.Returning the seat to seating positionWARNING: Before re

To close the cupholders:• Push the front edge back into the seat until the cupholders are fullyseated.• Make sure there is nothing in the cupholders b

• Push the indicated side of thecontrol for minimum heat.• Push again to deactivate.The heated seat module resets at every ignition run cycle. While t

How does the Personal Safety System™ work?The Personal Safety System™ can adapt the deployment strategy of yourvehicle’s safety devices according to c

in rear-facing child seats, this occurs because they are initially sittingvery close to the airbag. For other occupants, this occurs when theoccupant

Front outboard safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts

AdvanceTrac威/Traction control(RTT) (if equipped): Displayswhen the AdvanceTrac威/Tractioncontrol is active. If the light remainson, have the system ser

Safety restraints precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

Regular Cab Center front safety beltWARNING: Always use both lap and shoulder safety belt in theRegular Cab center seating position.If you carry large

1. To lengthen the lap belt, pullsome webbing out of the shoulderbelt retractor.2. While holding the webbing belowthe tongue, grasp the tip (metalport

While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, t

Shorten and fasten the belt whennot in use.For long term storage, the lap belt can be placed into a pocket found onthe inside lid of the storage compa

Energy management retractorsYour vehicle has a safety belt system equipped with energy managementretractors at the driver and front outboard passenger

How to use the automatic locking mode1. Buckle the combination lap and shoulder belt.• Right front passenger seat• Rear seats (if equipped)2. Grasp th

WARNING: After any vehicle collision, the safety belt systemsat all seating positions (except the driver position, which doesnot have this feature) mu

Safety belt usage sensorsThe driver and front outboard passenger safety belt buckles areequipped with sensors that detect if the safety belts are fast

Anti-theft system: Flashes whenthe SecuriLock威 Passive Anti-theftSystem has been activated.Turn signal: Illuminates when theleft or right turn signal

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)The airbag supplemental restraint system is designed to work inconjunction with the safety belts to help pro

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

WARNING: Do not attempt to service, repair, or modify theairbag supplemental restraint systems or its fuses. Contact yourauthorized dealer as soon as

If two adults and a child occupy a Regular Cab, properly restrain thechild in the center front unless doing so would interfere with driving thevehicle

internal injuries, particularly to occupants who are not properlyrestrained or are otherwise out of position at the time of airbagdeployment. Thus, it

Platinum instrument clusterHarley Davidson instrument clusterInstrument Cluster192010 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

A difficulty with the system is indicated by one or more of the following:• The readiness lights will eitherflash or stay lit.• The readiness lights w

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

How does the Safety Canopy姞 system work?The design and development of theSafety Canopy威 system includedrecommended testing proceduresthat were develop

The Safety Canopy威 is mounted to roof side-rail sheet metal, behind theheadliner, above each row of seats. The Safety Canopy威 is designed toinflate be

If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot fun

Locks and Security 126Keys 126Locks 126Anti-theft system 138Seating and Safety Restraints 147Seating 147Safety restraints 166Airbags 185Child restrain

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

WARNING: All children are shaped differently. TheRecommendations for Safety Restraints are based on probablechild height, age and weight thresholds fr

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeLargerchildrenChildren who have outgrown

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi

Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing

If you are using a Regular Cab center seat, see Installing child safetyseats in cinch tongue combination lap and shoulder belt seatingposition later i

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

WARNING: Always use both lap and shoulder safety belt in theRegular Cab center seating position.1. Position the child safety seat inthe Regular Cab ce

Tachometer (if equipped):Indicates the engine speed inrevolutions per minute. Driving withyour tachometer pointercontinuously at the top of the scalem

3. Slide the tongue up the webbing.4. While holding both shoulder andlap portions next to the tongue,route the tongue and webbingthrough the child sea

6. While pushing down with yourknee on the child seat pull up onthe shoulder belt portion to tightenthe lap belt portion of thecombination lap and sho

WARNING: Never place a rear-facing child seat in the frontcenter seating position of a vehicle with rear seating positions.1. Lengthen the lap belt. T

Your vehicle is equipped with LATCH lower anchors for child seatinstallation at the following seating positions (LATCH is not available onF150 Regular

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

point called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Contact the manufacturer of yourchild seat

Front seat tether strap attachment1. Route the child safety seat tether strap over the back of the seat andunder the head restraint.For vehicles with

Rear seat tether strap attachmentThere are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow) in the

3. Tighten the tether strapaccording to the child seatmanufacturer’s instructions.If the safety seat is not anchored properly, the risk of a child bei

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

Yellow area (warning) — thetransmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. snowp

• High back booster seatsIf, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat may improve thisconditio

WARNING: Failure to inspect and if necessary replace thesafety belt assembly or child restraint system under the aboveconditions could result in sever

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

MYKEY MILES (km) (if programmed)For more information, refer to MyKey™ in the Locks and Securitychapter.MILES (km) TO EThis displays an estimate of app

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your

Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

HOLD RESET FOR SETUP MENUPress and hold the SELECT/RESET stem when this message is displayedto get into the SETUP menu. The following setup items are

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is inuse. Repair the

TPMS reset procedureThe TPMS reset procedure needs to be performed after each tirerotation on vehicles that require different recommended tirepressure

3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff 3 times. This must beaccomplished within ten second

8. Remove the valve cap from the valve stem on the right rear tire.Decrease the air pressure until the horn sounds.9. Remove the valve cap from the va

Follow these guidelines when using snow tires and chains:• Use only SAE Class S chains.• Install chains securely, verifying that the chains do not tou

Press the SELECT/RESET stem to turn autounlock on or off.EASY ENTRY (if equipped)This feature automatically moves the driver’s seat backwards for easy

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Your vehicle’s load capacity is designated by weight, not by volume, soyou cannot necessarily use all available space when loading a vehicle.Towing a

Regular Cab 4x2 (145” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 2V3.55 10600 (4808) 5500 (2495)3.73 11100

SuperCab 4x2 (145” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)5.4L3.15 14000 (6350) 8600 (3900)3.55 15200 (6895

1. XXX% OIL LIFE2. CHARGING SYSTEM3. DOOR STATUS4. BRAKE SYSTEM5. XX MILES TO E FUEL LEVEL XXX6. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer

SuperCrew 4x2 (145” wheelbase)Engine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)4.6L 2V3.55 10600 (4808) 5200 (2359)3.73 11100 (

SuperCrew 4x4 (145” wheelbase) Harley-Davidson VersionEngine Rear axle ratio MaximumGCWR-lb. (kg)Maximumtrailerweight-lb. (kg)5.4L 3.73 11200 (5080) 5

Note: Do not exceed trailer weight of 5,000 lb. (2,268 kg) when towingwith bumper only.Preparing to towUse the proper equipment for towing a trailer a

Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci

The trailer brake controller (TBC) is designed to display three items ofinformation in the instrument cluster message center. These are: gainsetting,

The GAIN should be set to provide the maximum trailer brakingassistance while ensuring the trailer wheels do not lock when braking.Locked trailer whee

Note: Your TBC can be diagnosed by your authorized dealer todetermine exactly which trailer fault has occurred; however, if the faultis with the trail

Trailer lampsTrailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working.

Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni

Exceeding these limits may allow water to enter vehicle components:• causing internal damage to the components.• affecting driveability, emissions and

REAR LEFT DOOR AJAR— Displayed when the rear left door is notcompletely closed.REAR RIGHT DOOR AJAR— Displayed when the rear right door isnot complete

In case of a roadside emergency with a disabled vehicle, see Wreckertowing in the Roadside Emergencies chapter.4WD vehicles equipped with an electroni

STARTINGPositions of the ignition1. Off — locks the automatictransmission gearshift lever andallows key removal.Note: The ignition key cannot beremove

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

• 6–speed transmission4. Make sure the parking brake isset.5. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will brie

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start).2. Turn the key to 4 (start), thenrelease the key as soon as theengin

If you should experience cold weather starting problems on E85ethanol,and neither an alternative brand of E85ethanol nor an engine blockheater is avai

WARNING: Failure to follow engine block heater instructionscould result in property damage or physical injury.WARNING: To reduce the risk of electrica

• Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working order.How to use the engine block heate

Using ABSWhen hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness

WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m

OIL CHANGE REQUIRED— Displayed when an oil change is required.XX%OIL LIFE CHANGE SOON—Displayed when an oil change willsoon be required and shows the

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the “sliding car” iconwillilluminate steadily. Verify that the Advanc

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

The Roll Stability Control™ system may be deactivated in certainsituations. See the Switching off AdvanceTrac威 with RSC威 sectionfollowing.Switching of

AdvanceTrac威 with RSC威 FeaturesButtonfunctions“Sliding car”iconRSC威 ESC TCSVehicle speedexceeds 35 mph(56 km/h) afterbutton ispressed andheld for more

Disabling trailer sway controlTrailer sway control can be disabled during any key cycle. See trailersway control under the Message center in the Instr

LIMITED-SLIP AXLE (IF EQUIPPED)This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

3. Turn the steering wheel one-halfturn to access the slots on each sideof the steering wheel.4. Insert a flat head screwdriver intoeach slot to unsna

6. Reinstall the steering column cover, start the vehicle and release theparking brake.Note: After the transmission is shifted to N (Neutral), it is e

SHIFT DELAYED PULL FORWARD (if equipped)— May displaywhen shifting to or from 4X4 LOW. For more information, refer toFour-wheel drive (4WD) operation

If the fuse is not blown and the brakelamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. Ap

AUTOMATIC TRANSMISSION OPERATIONUnderstanding the gearshift positions of the 4–speed automatictransmissionYour vehicle has been designed to improve fu

WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key

• O/D (Overdrive) is automatically returned each time the key is turnedoff.2 (Second)This position allows for second gear only.• Provides engine braki

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Press the brake pedal• Start the en

• Column-shift transmission• Floor-shift transmissionThe TOW HAUL indicator light willilluminate in the instrument cluster.Tow/Haul delays upshifts to

WARNING: Do not use the Tow/Haul feature when driving in icyor slippery conditions as the increased engine braking can causethe rear wheels to slide a

REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the tailgate, provides avideo image, which appears in therearview mirror or

Customer Assistance 346Reporting safety defects (U.S. only) 352Reporting safety defects (Canada only) 352Cleaning 353Maintenance and Specifications 36

CHECK SPEED DRIVE SAFELY — Displayed when a MyKey™ is inuse and the optional setting is on and the vehicle exceeds a preselectedspeed. Refer to MyKey™

Note: The default setting for the rear camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set therear cam

Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe system inspected by your authorized dealer.• If the image is not cle

• 4X4 LOW - Illuminates when 4Lis selected.•- Illuminates when theelectronic locking differential(ELD) is selected (if equipped).• CHECK 4X4 - Display

Note: Momentarily releasing the accelerator pedal while preforming ashift will improve engagement/disengagement times.Note: Do not perform this operat

Using the electronic shift 4WD system (if equipped)2H (4X2) - Power to the rearwheels only; used for street andhighway driving. Provides optimalsmooth

If SHIFT DELAYED PULL FORWARD is displayed in the messagecenter, transfer case gear tooth blockage is present. To alleviate thiscondition, place the t

Shifting between AWD (Auto) and 4H (High)Move the control from AWD to 4H at a stop or while driving at anyspeed. The message center will display “AWD”

Activating the electronic locking differential (ELD)The ELD can be turned on bypulling the knob on the 4WD controltoward you while the control is inei

Maintain steering wheel control at all times, especially in rough terrain.Since sudden changes in terrain can result in abrupt steering wheelmotion, m

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

Refer to UNITS later in this section to switch the display from Metric toEnglish.MYKEY MILES (km) (If programmed)For more information, refer to MyKey™

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

found in the Maintenance and Specifications chapter. You shouldbecome thoroughly familiar with this information before you operateyour vehicle.Normal

Driving through deep water may damage the transmission.If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced.After dri

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

WARNING: If you are driving in slippery conditions that requiretire chains or cables, then it is critical that you drive cautiously.Keep speeds down,

Once through the water, always dry the brakes by moving yourvehicle slowly while applying light pressure on the brake pedal.Wet brakes do not stop the

• Front wheel toe may require re-adjustment to prevent prematureuneven tire wear. Specifications are found in the Ford WorkshopManual.• Headlight aim

WARNING: Do not attempt to service, repair, or modify the airbag supplemental restraint system (SRS) or its fuses. See yourFord or Lincoln Mercury dea

Factory installed snow plow prep package vehicles already have beenprogrammed with the unique power train control strategy to provideproper cooling. I

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

For more information refer to Essentials of good fuel economy in theMaintenance and Specifications chapter.MPG (L/km)This displays instantaneous fuel

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equip

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To reinstall the fuse box cover, place the top part of the cover on thefuse panel, then push the bottom part of the cover until you hear it clickshut.

Fuse/RelayLocationFuse AmpRatingProtected Circuits9 15A Interior courtesy lights, Cargolamps10 15A Backlighting, Puddle lamps11 10A GPS module12 7.5A

Fuse/RelayLocationFuse AmpRatingProtected Circuits33 10A Trailer brake controller34 5A Electronic locking differentialindicator35 10A Rear park assist

WARNING: To reduce risk of electrical shock, always replacethe cover to the Power Distribution Box before reconnecting thebattery or refilling fluid r

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 30A** Power running board motors12 40A** Electric fan13 30A** Starter relay14 30A** Passenger pow

Fuse/RelayLocationFuse AmpRatingProtected Circuits39 — Back up lamps relay40 — Electric fan relay41 15A* Heated mirror42 — Not used43 20A* Backup lamp

Fuse/RelayLocationFuse AmpRatingProtected Circuits67 — Not used68 20A** 4x4 module69 30A** Passenger heated/cooled seats70 — Not used71 — Not used72 2

9. MYKEY(S) PROGRAMMED10. ADMIN KEYS PROGRAMMEDOIL LIFEThis displays the remaining oil life.An oil change is required whenever indicated by the messag

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe

• Wet weather driving capability• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the full-siz

To remove the jack on SuperCrew models:1. Lift both rear seat cushions.2. Remove the insert containing the Easy Fuel ™ funnel from the driver’sside.3.

WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h

• FrontNote: Use the frame rail as the jacking location point, NOT the controlarm.Note: For F-150 SVT Raptor, you must always use the jack saddleexten

6. Remove the lug nuts with the lug wrench.7. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lu

3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases s

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

AUTOUNLOCKThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.Pres

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

Waiting four seconds or pressing the RESET button cycles the messagecenter through each of the language choices.Press the RESET button to set the lang

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• After polishing chrome bumpers, apply a coating of Motorcraft威Premium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent q

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

5.4L ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dea

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A),available from your a

For removal of fine scuffs and scratches, use Scotch-Brite威 MicrofiberCloth or cheese cloth along with Motorcraft Premium Liquid Wax(ZC-53-A), Motorcr

be completely cleaned by this method, the area may be cleaned using acommercially available cleaning product designed for automotiveinteriors.3. If ne

CHECK CHARGING SYSTEM— Displayed when the electrical systemis not maintaining proper voltage. If you are operating electricalaccessories when the engi

• If the leather cannot be completely cleaned using a mild soap andwater solution, the leather may be cleaned using a commerciallyavailable cleaning p

ScratchesNatural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suc

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. Go to the front of the vehicle a

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L V81. Windshield washer fluid reservoir2. Transmission fluid dipstick (4.6L 2V only)3. Brake fluid

5.4L V81. Windshield washer fluid reservoir2. Engine oil dipstick3. Brake fluid reservoir4. Engine coolant reservoir5. Air filter assembly6. Power ste

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the bl

5. Locate and carefully remove theengine oil level dipstick.6. Wipe the dipstick clean. Insertthe dipstick fully, then remove itagain.• If the oil lev

WIRING FAULT ON TRAILER (if equipped)— Displayed if there arecertain faults in the vehicle wiring and trailer wiring/brake system. Referto Trailer tow

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by th

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the FULL COLD level or within theCOLD

• Do not mix coolants. Add the coolant type originally equippedin your vehicle. Refer to Maintenance product specifications andcapacities in this chap

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap.5. Fill the coolant reservoi

• NEVER increase the coolant concentration above 60%.• Increased engine coolant concentrations above 60% willdecrease the overheat protection characte

• The light will illuminate.If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder ope

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

TRAIN RIGHT FRONT TIRE (if equipped)— Displayed whentraining the TPMS system. Refer to TPMS reset procedure in the Tires,Wheels and Loading chapter fo

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

When fueling your vehicle:1. Turn the engine off.2. Open the fuel filler door.3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump

Flex Fuel Vehicle (FFV) fuel fill inletIf your vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet.Choosing the r

Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily under mostdriving conditions while you areusing fuel with the

Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the rightf

1. Locate the white plastic funnel. Itis located under the second rowdriver side seat near the spare tiretool box.2. Slowly insert the funnel into the

vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the emp

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel econom

BUCKLE UP TO UNMUTE AUDIO — Displayed when a MyKey™ is inuse and Belt-Minder威 is activated. Refer to MyKey™ in the Locks andSecurity chapter for more

If other than Ford, Motorcraft威 or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control,

2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel fill inlet may not have been properly closed. See Easy Fuel™

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX

7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated area for normal operating temperature or ambienttemperature.L

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil

Changing the air filter element1. Locate the mass air flow sensorelectrical connector on the air outlettube. This connector will need to beunplugged.2

5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co

CONGRATULATIONSCongratulations on acquiring your new Ford Motor Company product.Please take the time to get well acquainted with your vehicle by readi

AUDIO SYSTEMSNote: If your volume is muted and MYKEY VOLUME LIMITED isdisplayed, refer to MyKey™ in the Locks and Security chapter for moreinformation

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford specificationBrake fluidBetweenMIN/MAX

Item CapacityFord part name orequivalentFord part number /Ford specificationCooling system stopleak pellets—Motorcraft威 CoolingSystem Stop Leak Pellet

Item CapacityFord part name orequivalentFord part number /Ford specificationAutomatic transmissionfluid (6R80)12.1 quarts(11.4L)6(4.6L 3V engine)Motor

Item CapacityFord part name orequivalentFord part number /Ford specificationFuel tankReg. Cab 8’ box /SuperCab 6.5’ box /SuperCab 8’ box26.0 gallons(9

ENGINE DATAEngine4.6L 2V V8engine4.6L 3V V8engine5.4L V8 engineCubic inches 281 281 330Fuel87 octane 87 octane 87 octane orEthanol (E85)Firing order 1

Engine drivebelt routingIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations req

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Bed side stepInterior cargo organization and managementTruck bed cargo organization and managementTowing mirrorsTrailer hitches, wiring harnesses and

1. / : Press / tomanually go up or down the radiofrequency. Press and hold for a fastadvance through radio frequencies.Also use in AUDIO mode to gain

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan4122010 F-150 (f12)Owners Guide, 1st PrintingUSA (fus)

AAccessory delay ...93AdvanceTrac ...279Air cleaner filter ...396–397, 399Air conditioning ...

Child safety seats ...204attaching with tether straps ..214in front seat ...205, 211in rear seat ...

coolant ...373fail-safe cooling ...377idle speed control ...371lubrication speci

Heatingheating and air conditioningsystem ...59, 62, 64, 67Homelink wireless controlsystem ...1

MyKey ...141NNavigation system ...58OOctane rating ...383–384Oil (see Engine

Safety restraints - LATCHanchors ...212Safety seats for children ...204Safety ComplianceCertification Label

Transmission ...291brake-shift interlock(BSI) ...287, 289fluid, checking and adding(automatic)

6. ON/OFF/Volume: PressVOL-PUSH to turn ON/OFF. TurnVOL-PUSH to increase/decreasevolume.7. CLK (Clock): Press CLK totoggle between displaying the radi

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution

SEEK: Press SEEK to access the previous/next strong radiostation.SCAN: Press for a brief sampling of all strong radio stations.0–9 (MEMORY PRESETS): W

CD/MP3 PlayerCD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will begin where it ended last. If no CD is loade

SCAN: Press for a brief sampling of all tracks on the current disc orMP3 folder.DIRECT:In CD mode– Press DIRECT. The display will read DIRECT TRACKMOD

cancel your entry by pressing DIRECT. If an invalid station number isentered, INVALID CHANNEL will appear in the display and the systemwill continue p

display. After a category is selected, press SEEK to search forthat specific category of channels only (i.e. ROCK). You may alsoselect CATEGORY ALL to

• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press theto scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL: Press

Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a

Use SEEK to adjust between SPEED OFF and levels 1–7:Increasing the level from 1 (lowest setting) to 7 (highest setting) allowsthe radio volume to auto

The Auxiliary Input Jack provides away to connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music

2. Do not set the portable music player’s volume level higher than isnecessary to match the volume of the CD or FM radio in your audiosystem as this w

GENERAL AUDIO INFORMATIONRadio frequencies:AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio

CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.”• If you

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Messag

4. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve cooling performance and efficiency. A/Cengages automaticall

12. – Front fan speed control: Press to decrease the fan speed.13. A.RRear defroster (if equipped): Press to activate/deactivatethe rear window defros

3. Manual override control: Allows you to manually select whereairflow is directed. To return to full automatic control, press AUTO.When choosing to c

9. PASS TEMP: Press to engage/disengage separate passenger sidetemperature control. Turn to increase/decrease the air temperature onthe passenger side

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED AND COOLED SEATS(NAVIGATION BASED–IF EQUIPPED)Temperature conversion: To switch between Fahrenheit

4. Passenger temperature: Press to activate separate passengertemperature control to increase/decrease the air temperature on thepassenger side of the

of fog and thin ice. The system will automatically provide outside air toreduce window fogging. Press this button again to return to the previousair f

NOTICE TO OWNERS OF THE F150Note: Your vehicle is equipped with high performance tires. When firstdriving the vehicle after it has been parked for a p

VOICE COMMANDS IN CLIMATE MODEPlease refer to the Voice commands in climate mode section of theNavigation supplement for more information on using voi

To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan

HEADLAMP CONTROLRotate the headlamp controlclockwise to the first positiontoturn on the parking lamps.Rotate clockwise to the secondpositionto also tu

At this point, the headlamps and park lamps will turn off.Fog lamp control (if equipped)The headlamp control also operatesthe fog lamps. The fog lamps

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.In order for the DRLs to function:• the ignition must be in the

Vertical aim adjustment1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away.• (1) 8 fe

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.Push and hold up or down to the first detent

Rear dome/courtesy lamps (if equipped)The dome lamp lights when:• any door is opened.• the instrument panel dimmerswitch is rotated up until thecourte

Ambient lighting (if equipped)Illuminates footwells and cupholderswith a choice of several colors. Theambient lighting control is locatedon the floor

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access e

2. Remove the pushpin that holdsthe air deflector/protective coverfrom the upper inboard corner ofthe lamp.3. Loosen the three retaining bolts(two at

Install the new bulb in reverse order.Replacing front parking lamp/turn signal/sidemarker bulbs1. Make sure that the headlamp control is in the off po

3. Carefully pull the lamp assemblystraight rearward from the tailgatepillar to disengage two hiddensnap-in retainers. (Flare side taillamps are not e

Replacing exterior mounted mirror turn signal indicator lamp bulbsFor bulb replacement, see your authorized dealer.Replacing license plate lamp bulbsT

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Windshield washer: Press the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick press and hold: thewipers wi

POWER TILT STEERING (IF EQUIPPED)The steering column can beadjusted manually by moving thetwo-way rocker adjustment controllocated below the turn sign

On vehicles with memory feature, to prevent damage to the steeringcolumn, the steering column is designed to set a stopping position justshort of the

CENTER CONSOLE (IF EQUIPPED)The center console offers several useful storage features. These include:1. Cupholders2. Tissue holder in lid3. Power poin

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons.3. Slowly d

• do not leave battery chargers, video game adapters, computers andother devices plugged in overnight or when the vehicle is parked forextended period

Press and pull the window switchesto open and close windows.• Press down (to the first detent)and hold the switch to open.• Pull up (to the first dete

Power sliding back window (if equipped)Press and hold thethe controlto open the window all the way tothe full open position.Pull and hold thecontrol t

The mirrors will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up.Do

Fold-away mirrorsFold the side mirrors in carefullybefore driving through a narrowspace, like an automatic car wash.Powerfold mirrors (if equipped)Wit

On vehicles not equipped with rear defrost, press the heated mirrorcontrol located on the climate control panel. For more informationrefer to the Clim

Press and hold the rocker control toadjust accelerator and brake pedal.• Press the right side of the controlto adjust the pedals toward you.• Press th

• When this feature is enabled (AUTO), the running boards will moveback to the correct positions based off of the door positions.Bounce-back:• If an o

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas