Ford 2010 Fusion Hybrid v.2 Manual do Utilizador

Introduction 4Instrument Cluster 18Warning lights and chimes 18Gauges 25Message center 34Entertainment Systems 50AM/FM stereo with CD/MP3 50Auxiliary

Frequently asked questionsQuestion AnswerWhat are the series ofclicks from the cargo areawhen I first turn the key inthe ignition?The high voltage bat

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart locksThis feature attempts to help prevent you from lo

Deactivating/activating autolock featureYour vehicle comes with the autolock features activated; there are fourmethods to enable/disable this feature:

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The h

the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including i

The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the o

Replacing the batteryThe Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent.To replace the battery:1. Tw

Question AnswerWhy does my engine stayON when it’s extremelycold outside?In order to ensure that the climatecontrol system can begin heating thecabin

Illuminated entryThe interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter is used to unlock the door(s).The

1. Place the key in the ignition andturn the ignition to the 3 (on)position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the trunk.Th

The anti-scan feature will turn off after:• one minute of keypad inactivity.• pressing thecontrol on the remote entry transmitter portion ofyour Integ

Note: Large metallic objects, electronic devices that are used topurchase gasoline or similar items, or a second coded key on the samekey chain may ca

Automatic disarmingThe vehicle is disarmed immediately after the ignition is turned to the onposition.The theft indicator will illuminate for three se

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

PERIMETER ALARM SYSTEMThe perimeter anti-theft system will help protect your vehicle fromunauthorized entry.If there is any potential perimeter anti-t

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by using the remote entry transmitter portion ofyour

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

Question AnswerWhat is the engine oilchange service interval?The engine oil should be changed every10,000 miles (16,000 km) under normaloperating cond

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Using the manual recline functionWARNI

Adjusting the front power seatWARNING: Never adjust the driver’s seat or seatback when thevehicle is moving.WARNING: Do not pile cargo higher than the

The control is located on the outboard side of the seat cushion.Move the switch in the direction ofthe arrows to raise or lower thefront portion of th

Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur

REAR SEATSNote: Do not block the air inlet at the front facing of the rear seatcushion. The air needs to be able to flow through the air inlet without

To adjust the head restraint, do the following:1. Raise the head restraint bypulling up on the head restraint.2. Lower the head restraint bypressing a

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Insert and p

To reinstall the adjustable head restraint, do the following:1. Insert the two stems into theguide sleeve collars.2. Push the head restraint downuntil

WARNING: Front seat mounted rear-facing child or infant seatsshould NEVER be placed in front of an active passenger airbag.DATA RECORDINGService Data

Seat-mounted cup holders and armrest storage compartmentTo access the cup holders, fold thearmrest down.WARNING: Use only soft cups in the cup holder.

How does the Personal Safety System™ work?The Personal Safety System™ can adapt the deployment strategy of yourvehicle’s safety devices according to c

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupant

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Combination lap and shoulder belts1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of l

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

WARNING: Position the safety belt height adjusters so that thebelt rests across the middle of your shoulder. Failure to adjustthe safety belt properly

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

Ford of Canada do not access event data recorder informationwithout obtaining consent, unless pursuant to court order orwhere required by law enforcem

The Belt-Minder威 feature uses two different warning chimes. During thefirst minute of activation, the warning chime will sound once everysecond. The r

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

1. Turn the ignition switch to the on position. DO NOT START THEENGINE.2. Wait until the safety belt warning light turns off (Approximately1–2 minutes

WARNING: Do not put anything on or over the airbag cover.Placing objects on or over the airbag cover may cause thoseobjects to be thrown by the airbag

Steps you can take to properly position yourself away from the airbag:• Move your seat to the rear as far as you can while still reaching thepedals co

How does the safety belt pretensioner and airbag supplementalrestraint system work?The safety belt pretensioner andairbag SRS are designed to activate

are not properly restrained or are otherwise out of position at the timeof airbag deployment. Thus, it is extremely important that occupants beproperl

Knee airbag system (driver’s side only)The knee airbag is located under the instrument panel. The systemworks along with the driver’s front airbag to

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use extreme caution

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness light in theinstrument cluster will stay lit.If the airbag read

A difficulty with the system is indicated by one or more of the following:• The readiness light (same lightfor front and side airbag system)will eithe

How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b

WARNING: If the sideairbag has deployed, theairbag will not function again.The side airbag system(including the seat) must beinspected and serviced by

WARNING: Do not place objects or mount equipment on ornear the headliner at the siderail that may come into contactwith a deploying side air curtain.

How does the side air curtain system work?The design and development of theside air curtain system includedrecommended testing proceduresthat were dev

passenger seat or an unbuckled child or small person in the passengerseat. The air curtain was designed to inflate between the side windowarea and occ

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommended re-straint typeInfantsor tod-dlersChildren weighing 40

Recommendations for attaching child safety restraints for childrenRe-straintTypeChildWeightUse any attachment method as indicated be-low by “X”LATCH(l

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi

Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing

To reinstall the head restraint, linethe posts up in the holes on the seatback with the head restraint strapfacing the outside of the vehicle andpush

When installing a child safety seat with combination lap/shoulder belts:• Use the correct safety belt buckle for that seating position.• Insert the be

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

2. Locate the correct anchor for theselected seating position.3. Open the tether anchor cover.4. Clip the tether strap to theanchor as shown.If the te

Although the lap/shoulder belt will provide some protection, childrenwho have outgrown a typical child seat are still too small for lap/shoulderbelts

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor ⬙blowout⬙, with unexpecte

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

WARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcause an explosion.

• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram)Sometimes irregular tire wear can be corrected by rotating the t

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

emission control system during normal driving. If the vehicle needsI/M testing, refer to the Readiness for Inspection/Maintenance (I/M)testing section

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

11. Maximum Load: Indicates the maximum load in kilograms andpounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter

To restore the full functionality of the Tire Pressure Monitoring System,have the damaged road wheel/tire repaired and remounted on yourvehicle. For a

Low TirePressureWarningLightPossible cause Customer Action RequiredFlashingWarningLightSpare tire in use Your temporary spare tire is in use.Repair th

SNOW TIRES AND CHAINSThe original equipment tires on your vehicle have an all-weather treaddesign to provide traction, handling, and braking performan

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Locks and Security 100Keys 100Locks 101Anti-theft system 113Seating and Safety Restraints 119Seating 119Safety restraints 130Airbags 143Child restrain

WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment.Tires, Wheels and Loading2002010

GAW (Gross Axle Weight) – is the total weight placed on each axle(front and rear) – including vehicle curb weight and all payload.GAWR (Gross Axle Wei

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the l

RECREATIONAL TOWINGAn example of “recreational towing” is towing your vehicle behind amotorhome.Note: Put your climate control system in recirculated

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra

order to warm the engine. If the engine idle speed does not slow downautomatically, have the vehicle checked.Before starting the vehicle:1. Make sure

Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning

Guarding against exhaust fumesCarbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects.WARNING: If you smell exhaus

chime will also sound to remind you to fasten your safety belt. Refer tothe Seating and Safety Restraints chapter to activate/deactivate theBelt-Minde

• Do not use multiple extension cords. Instead, use one extension cordwhich is long enough to reach from the engine block heater cord tothe outlet wit

and should be inspected by an authorized dealer. If the vehicle hascontinuous vibration or shudder in the steering wheel while braking, thevehicle sho

Regenerative Braking System (RBS)Your vehicle uses a feature known as regenerative braking. This is usedto simulate the engine braking of an internal

WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park) (automatictransmission) or in 1 (First) (m

Your vehicle is equipped with the AdvanceTrac威 system. TheAdvanceTrac威 system provides the following stability enhancementfeatures for certain driving

Traction Control System (TCS)Traction control is a driver aid feature that helps your vehicle maintaintraction of the wheels, typically when driving o

Certain adverse driving maneuvers may activate ESC, which include butare not limited to:• Taking a turn too fast• Maneuvering quickly to avoid an acci

AdvanceTrac威 FeaturesControlswitchfunctions“Slidingcar” icon“Sliding caroff”iconESCTractioncontrolDefault atstart-upIlluminatedduring bulbcheckIllumin

WARNING: The EPS system has diagnostics checks thatcontinuously monitor the EPS system to ensure proper operationof the electronic system. When an ele

If you cannot move the gearshift lever out of P (Park) with ignition inthe on position and the brake pedal pressed, it is possible that a fuse hasblow

Engine oil pressure (RTT):Illuminates when the oil pressurefalls below the normal range. Themessage center displays LOW OILPRESSURE when the engine oi

WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key

N (Neutral)With the gearshift lever in N (Neutral), the vehicle is free to roll; holdthe brake pedal down while in this position. Because of the uniqu

REVERSE SENSING SYSTEM (IF EQUIPPED)The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Rev

The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system,located on the trunk, provides avideo image which appears in therearview mirror or on t

The camera lens for the camera is located on the trunk. Keep the lensclean so that the video image remains clear and undistorted. Clean thelens with a

BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)The BLIS威 is a convenience featurethat aids the driver in assessingwh

The BLIS威 will trigger the alert for vehicles that enter your blind zonefrom the rear or merge in to the blind zone from the side. Vehicles thatyou pa

Cross traffic alert (CTA) system operationThe CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backi

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed tovehicle on left]).

Low tire pressure warning:Illuminates to warn you when yourtire pressure is low. If the telltaleremains on solid at start up or whiledriving, the tire

CTA and Reverse Sensing System (RSS) interactionCTA works along with the Reverse Sensing System (RSS) (if equipped).Become familiar with the warning t

WARNING: Just prior to the system recognizing a blockedcondition and alerting the driver, the number of missed objectswill increase. To help avoid inj

Trailer tow false alertsWhen towing a trailer, the left and right sensor may detect the trailerthus causing a false alert. It may be desirable to turn

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Driver smart window motor2 15A Brake on/off switch, Centerhigh-

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Not used (Spare)12 7.5A Power outside mirrors13 5A SYNC module14 10A Electronic Finish Panel

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 5A Passive Anti-Theft Sensor (PATS)transceiver37 10A Humidity sensor38 20A Subwoofer amplifier39

Door ajar (RTT): Displays whenthe ignition is in the on position andany door is open. A message mayalso display in the message center.Turn signal: Ill

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A* Electronic power assist steeringB+2 50A* Electron

Fuse/RelayLocationFuse AmpRatingProtected Circuits13 15A** Motor electronics coolant/heaterpump (relay 42 & 44 power)14 — Not used15 — Not used16

Fuse/RelayLocationFuse AmpRatingProtected Circuits36 1A Diode Fuel pump37 5A** Vacuum pump monitoring38 10A** Heated side mirrors39 10A** Transmission

Auxiliary relay boxThe auxiliary relay box is located in front of the radiator in the enginecompartment.The components are coded as follows:Relay Loca

(TPMS) in the Tires, Wheels and Loading chapter. Replace the sparetire with a road tire as soon as possible. During repairing or replacing ofthe flat

• Use more than one dissimilar spare tire at a time• Use commercial car washing equipment• Try to repair the dissimilar spare tireUse of one of the di

Stopping and securing the vehicle1. Park on a level surface, set the parking brake and activate the hazardflashers.2. Place the gearshift lever in P (

Tire change procedureWARNING: To help prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth dire

3. Put the jack in the jack locatornext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Note: T

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

GAUGESYour vehicle is equipped with an LCD (Liquid Crystal Display),reconfigurable instrument cluster. You can choose from four informationlevels, and

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface

JUMP STARTING(LOW VOLTAGE [UNDERHOOD] BATTERY ONLY)WARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. A

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Emergency towingIn case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport veh

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

Enlighten instrument cluster (standard cluster shown, metricsimilar)Displays unique hybrid vehicle gauges, along with many of the familiargauges from

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inCentral America, the Caribbean, or the Middle East, contact the nearestauthorized

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

Empower instrument cluster (standard cluster shown, metric similar)The most information-rich display, with gauges designed to allow driversto decide f

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft威 Spot and Stain Remover (ZC-14). In Canada, useMotorcraft威 Mul

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

Working with the engine on1. Set the parking brake and shift to P (Park).2. Block the wheels.WARNING: To reduce the risk of vehicle damage and/orperso

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Engine oil filler cap3. Engine oil dipstick4. Motor/Electronics (M/E) co

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaningchapter.To prolong

• If the oil level is below the lower hole/line, engine oil must be addedto raise the level within the normal operating range.• If required, add engin

to the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andApproval

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with

Empower instrument cluster level only: The indicator next to thegauge will illuminate in green or white to indicate the following:•Indicator white: Th

3. Run the vehicle until the engine reaches normal operatingtemperature.4. Allow the engine to idle for at least one minute.5. Step on the accelerator

Checking engine coolantThe concentration and level ofengine coolant should be checked atthe intervals listed in scheduledmaintenance information. Thec

• Protection against rust and other forms of corrosion.• Enables calibrated gauges to work properly.Common instructions for cooling systems• The engin

• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling

6. Replace the cap. Turn until tightly installed. Cap must be tightlyinstalled to prevent coolant loss.After any coolant has been added, check the coo

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the tempera

WARNING: Automotive fuels can cause serious injury or deathif misused or mishandled.WARNING: Gasoline may contain benzene, which is acancer-causing ag

WARNING: When refueling always shut the engine off andnever allow sparks or open flames near the filler neck. Neversmoke while refueling. Fuel vapor i

Easy Fuel™ “no cap” fuel systemYour fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel fille

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

lost in a conventional vehicle. The regenerative braking system can beactivated by braking or coasting (i.e. even when you’re not pressing thebrake pe

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. If the proble

WARNING: Do not insert the nozzle of portable fuel containersor aftermarket funnels into the Easy Fuel™ system. This coulddamage the fuel system and i

Filling the tankWhen the fuel gauge indicates empty, there is still a small reserve of fuelin the fuel system. When refueling your vehicle after the f

the highway. This is contrary to conventional vehicles. However, many ofthe same actions that improve fuel economy in a conventional vehiclewill also

• Carrying unnecessary weight may reduce fuel economy (approximately1 mpg [0.4 km/L] is lost for every 300 lb [136 kg] of weight carried).• Adding cer

WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus

4. Driving through deep water—the electrical system may be wet.These temporary malfunctions can be corrected by filling the fuel tankwith good quality

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

AIR FILTERYour vehicle is equipped with a long life air filter. The air filter isdesigned to last the life of the vehicle. See your authorized dealer

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Customer Assistance 258Reporting safety defects (U.S. only) 264Reporting safety defects (Canada only) 264Cleaning 265Maintenance and Specifications 27

Efficiency leaves: Indicates shortterm driving efficiency, measuredover the last few minutes. The moreleaves and vines that are displayed,the more eff

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationeCVT transmissionfluid5.3 quarts(5.0L)3Motorcraft威MERCON威 LV ATF4XT-10-QLV

ENGINE DATAEngine 2.5L I4 engineCubic inches 152Required fuel 87 octaneFiring order 1-3-4-2Ignition system Coil on plugSpark plug gap 0.049–0.053 inch

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindRemote startVehicle security systemsWheel locksFor maximum vehicle performance, keep the following information inmind when adding accesso

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft威 or Ford authorized remanufacturedparts that are

Genuine Ford Parts and ServiceWhen planning your maintenance services, consider your Ford andLincoln Mercury dealership for all your vehicle’s needs.G

WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW?Owner Checks and ServicesRefer to Mileage Intervals for Additional Checks and ServicesCertain basic maint

reset this average at any time. Refer to Message center in this chapterfor more information on the average fuel economy display mode.If you calculate

Multi-point InspectionIn order to keep your vehicle running right, it is important that you havethe systems on your vehicle checked regularly. This ca

U.S. AND CANADIAN SCHEDULE5,000 miles (8,000 km)❑Inspect tires for wear and measure tread depth❑Rotate tiresDEALER VALIDATION:RO#: P&A CODE:DATE:M

30,000 miles (48,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for e

60,000 miles (96,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for e

90,000 miles (144,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for

120,000 miles (192,000 km)❑Change engine oil and replace oil filter❑Inspect tires for wear and measure tread depth❑Rotate tires❑Inspect wheel ends for

SPECIAL OPERATING CONDITIONSExtensive Idling and/or Low Speed Driving for Long Distances as in HeavyCommercial Use Such as Delivery, Taxi, Patrol Vehi

Current mileage goes here =>Add 50,000 miles to the current miles + 50,000Next change due at this mileage =>OrToday’s date goes here =>Add 3

Current mileage goes here =>Add 50,000 miles to the current miles + 50,000Next change due at this mileage =>OrToday’s date goes here =>Add 3

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Tachometer and EV mode gauge(Enlighten instrument clusterlevel only): When the gasolineengine is running, this gaugedisplays the engine speed inrevolu

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3212010 Fusion Hybrid (hfv)Owners Guide, 2nd PrintingUSA (fus)

AAccessory delay ...93AdvanceTrac ...213Air cleaner filter ...298Air conditionin

CCapacities for refilling fluids ...299CD ...50Cell phone use ...14Changing a t

Engine ...301cleaning ...267idle speed control ...278lubrication

lighting up panel andinterior ...76JJack ...243positioning ...

Power distribution box(see Fuses) ...239Power door locks ...101Power mirrors ...

Specification chart,lubricants ...299Speed control ...94Starting your vehicle ...206,

Accessory power gauge(Empower instrument clusterlevel only): This gauge indicateselectrical power demands from yourvehicle’s accessory systems.Accesso

Odometer: Registers the total miles(kilometers) of the vehicle.Refer to Message center in thischapter on how to switch thedisplay from Metric to Engli

Selectable featuresThe INFO, RESET and SETUPbuttons, located on the steeringwheel, control the message centerfunctions.Info menuThe top line of the di

Elapsed Drive Time 1 or 2Select this function from the INFO menu to display a timer.To operate this feature, do the following:1. Press and release RES

Setup menuThe setup menu can fully display on both the right and left sides of yourinstrument cluster. The left side contains the menu function while

While Display Settings is highlighted, press RESET to select it and moveright to display the following:Display ModeChoosing display mode allows you to

Press SETUP to scroll through the list and highlight one of the choices.Press RESET to pick the highlighted item.FE History LengthUse this to set the

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

UnitsWhile Units is highlighted, pressRESET to select it and move rightto display the following:• English• MetricPress SETUP to scroll through thelist

While Autolamp is highlighted, press RESET to select it and move rightto display the following autolamp delay values (in seconds):• 0 • 10• 20 • 30• 6

While Autounlock is highlighted, press RESET to select it and move rightto display the following:• On• OffPress SETUP to scroll through the list and h

While cross traffic is highlighted, press RESET to select it and moveright to display the following:• On• OffPress SETUP to scroll through the list an

To reset the oil monitoring system to 100% (or another value) after eachoil change perform the following:While Oil Life is highlighted, press RESET to

DemoThe demo briefly displays each ofthe gauge displays available.Press SETUP to reach Demo.While Demo is highlighted, pressRESET to start the demo. P

System warningsSystem warnings and important information about vehicle status will bedisplayed at the left side of your vehicle’s instrument cluster.

HIGH ENGINE TEMPERATURE — Displayed when the enginecoolant is overheating. Engine coolant temperature warning lamp willilluminate indicating coolant t

FUEL LEVEL LOW — Displayed as an early reminder of a low fuelcondition.BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake sys

CROSS TRAFFIC NOT AVAILABLE (if equipped) — Displayedwhen cross traffic alert is not available. See Blind spot informationsystem in the Driver Control

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

AUDIO SYSTEMSAM/FM/single CD or in-dash CD6/MP3 satellite compatible soundsystemWARNING: Driving while distracted can result in loss of vehiclecontrol

AM/FM Radio/ VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certain level a

RDS (Radio Data System) RadioAvailable only in FM mode. This feature allows you to searchRDS-equipped stations for a certain category of music format:

For a CD6 system– press EJECT and select the desired CD slot bypressing the corresponding memory preset #. The display will readEJECTING #. When the s

SHUFFLE: Press MENU repeatedly until SHUFFLE ON/OFF appears inthe display. Use SEEK/TRACK to switch between ON/OFF. Ifyou wish to engage shuffle mode

MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi

the system will take you to the channel playing the desired song. Youcan save up to 20 song titles. If you attempt to save more than 20titles, the dis

number and when the system accepts your entry it will displayENTER NEW PIN. Enter your new four-digit PIN and the system willsave the new PIN and PIN

For location and further information on auxiliary audio mode, refer toAuxiliary input jack later in this chapter.Refer to your SYNC威 supplemental info

To play your portable music player using the auxiliary input jack:1. Begin with the vehicle parked and the radio turned off.2. Ensure that the battery

BREAKING-IN YOUR VEHICLEYour vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,

location, such as the center console or the glove box, when the vehicle isin motion. The audio extension cable must be long enough to allow theportabl

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)Outside temperature (if equipped): The outside temperature willappear in the display and is labeled EX

4. : Distributes air through the windshield defroster vents, demistervents, floor vents and rear seat floor vents. The system will automaticallyprovid

12. MAX A/C: Activates air conditioning and distributes recirculated,conditioned air through the instrument panel vents to provide maximumcooling perf

• Vehicle speed above 47 mph (75 kmh)• Ascending a hill• Charge level of high voltage battery is low• Very high or low outside temperature (to provide

information. If your vehicle is equipped with both rear defroster andheated mirrors, the same button will activate both.3. A/C: Press to activate/deac

12. Defrost: Distributes outside air through the windshielddefroster vents and demister vents. Can be used to clear the windshieldof fog and thin ice.

VOICE COMMANDS IN CLIMATE MODEPlease refer to the Voice commands in climate mode section of theNavigation supplement for more information on using voi

To aid in side window defogging/demisting in cold weather:1. Select.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the low beam headlampso

4. Turn the headlamp control to the autolamp position. The headlampswill turn on.5. Wait the desired amount of time for the exit delay you want (up to

High beamsPush the lever toward theinstrument panel to activate. Pullthe lever toward you to deactivate.Flash to passPull toward you slightly to activ

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer control requires re-calibration. Press the dimmercontrol fr

5. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise

Your vehicle may also have readinglamps within the rear dome lamp(s).Press the switches on either side ofthe dome lamp to turn on thelamps.Ambient lig

The high voltage battery is cooled by cabin air drawn from vent holes inthe front of the rear seat cushions. Avoid placing objects at the ventholes wh

• Large water droplets, drip marks or streaks present on the interior ofthe lensTake your vehicle to dealer for service if any of the above conditions

Replacing interior bulbsCheck the operation of all bulbs frequently.Replacing exterior bulbsCheck the operation of all the bulbs frequently.Replacing

effective point to grasp the trunk side panel when pulling it out from theluggage scuff plate is at it’s bottom edge where that edge meets theexposed

Replacing fog lamp bulbs1. Make sure the fog lamp switch isin the off position.2. From underneath the vehicle,partially remove the tire splashshield b

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress on

Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p

Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t

INSTRUMENT PANEL STORAGE COMPARTMENTThe storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the stora

Driving to optimize fuel economyYour fuel economy should improve throughout your hybrid’s break-inperiod. As with any vehicle, fuel economy can be sig

Power point (110 VAC)The 110 VAC power point outlet,located on the rear of the floorconsole, is used for poweringelectrical devices that require up to

located in the top left corner is turned on. Refer to the indicator lightcode below for the power point status.Note: Using the 110 VAC power point for

To operate one-touch down:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes

Window lockThe window lock feature allows onlythe driver and front passenger tooperate the power windows.To lock out all the window controls(except fo

when the vehicle is put in (R) reverse. Refer to Rearview camerasystem in the Driving chapter.EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not a

Using speed controlThe speed controls are located on the steering wheel. The followingbuttons work with speed control:– SET +: Press to increase ordec

Increasing speed while using speed controlTo increase the set speed:• Press and hold SET + until you get to the desired speed, then release.You can al

SYNC威 system hands freecontrol featuresPressbriefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe radio display

To open the moon roof:The moon roof is equipped with anautomatic, one-touch, expressopening, closing and venting feature.Press and release the rear po

To vent:• To tilt the moon roof into the vent position (when the glass panel isclosed), press and release the front portion of the control.• To close